home

contact

pricing

technical information

    cold wire feed . feed units(WF-1, WF-3) . hand held torches . machine torches

cold wire feeders

download: Cold Wire Feed Manual (pdf) here

download: Cold Wire Feed Video here (14 min)

 

For complete installation of a Cold Wire TIG System, you need both the Cold Wire Feeder and a TIG torch (hand held or machine mounted) with cold wire TIG capabilities. The Cold Wire TIG System works independently of a standard TIG power supply using normal TIG welding parameters.

The WF-3 has an ON/OFF switch, pilot light, pulse/continuous feed switch, pulse wire on and off timers, remote switch receptacle, delay wire start and wire retract.
 

 

 

 

features

  • Automates adding of filler metal in TIG Welding.

  • All weld parameters can be duplicated.

  • Dual Groove Drive Roll system accepts multiple wire sizes.

  • Eliminates TIG rod stub loss.

  • Cabinet keeps filler wire clean.

  • Makes fully automatic machine TIG welding possible.

  • Results are consistent and high quality welds

 

front panel (WF-3) control

specifications

Voltage:
  Phase:
  Frequency:
  Height:
  Width:
  Length:
  Weight:
  Motor Type:
  Motor Rating:
  Filler Wire Spool Size:
  Filler Wire Sizes:

Wire Feed Speed Range:
Feed Time (pulsed mode):
Dwell Time (pulsed mode):
(WF-3 only) Delay Start Time:
(WF-3 only) Wire Retract Time:

 115V AC(220V AC 50 hz. -special item)
Single Phase
50 / 60 hz
15 in. (38.1 cm)
10 in. (25.4 cm)
21 in. (53.3 cm)
39 lbs. (17.7 kg)
DC permanent magnet
1/3 hp at 4000 rpm
12 in. (30.5 cm)
.023" (.5mm), .030" (.8mm), .035" (.9mm),
.045" (1.1mm), 1/16" (1.6mm).
0 - 500 ipm (0 - 1250cm)
continuously variable
continuously variable
continuously variable
continuously variable

 

WF3 COLD WIRE FEED UNIT
Application Drive Roll Wire Size Order Number
Hand Held / Machine Mounted 20-35DR .023"-.030" (.5mm-.8mm) WF3-030
30-45DR .030"-.045" (.8mm-1.1mm) WF3-035
45-564DR .045"-1/16" (1.1mm-1.6mm) WF3-045
45-564DR .045"-1/16" (1.1mm-1.6mm) WF3-116

 

RECOMMENDED COLD WIRE CONDUIT AND WIRE GUIDES
TIG TORCH WIRE SIZE WIRE TYPE

PART NUMBER
WIRE CONDUIT WIRE GUIDE
(TUBE & TIP)		 TUBE TIP BRACKET EXTENSION
BODY MOUNTED:


CWH180
CWH230
CWM230

 .023(.5mm) - .030(.8mm) HARD CW-FC CWG030B CWGB CWT030  
.023(.5mm) - .030(.8mm) SOFT NOT RECOMMENDED N/A N/A N/A  
.035 (.9mm) HARD CW-FC CWG035B CWGB CWT035  
.035 (.9mm) SOFT CW-FCN CWG035B CWGB CWT035  
.045 (1.1mm) HARD CW-FC CWG045B CWGB CWT045  
3/64 (1.2mm) SOFT CW-FCN116 CWG116B NONE NONE 3-WGBX-60
FRONT MOUNTED:


CWHTL300
CWH350
CWM350
CWMT400
CWMT500

 .023(.5mm) - .030(.8mm) HARD CW-FC CWG030H CWGH CWT030  
.023(.5mm) - .030(.8mm) SOFT NOT RECOMMENDED N/A N/A N/A  
.035 (.9mm) HARD CW-FC CWG035H CWGH CWT035  
.035 (.9mm) SOFT CW-FCN CWG035H CWGH CWT035  
.045 (1.1mm) HARD CW-FC CWG045H CWGH CWT045  
3/64 (1.2mm) SOFT CW-FCN116 CWG116H NONE NONE 3-WGBX-60
1/16 (1.6mm) HARD CW-FC116 CWG116H NONE NONE 3-WGBX-60
1/16 (1.6mm) SOFT CW-FCN116 CWG116H NONE NONE 3-WGBX-60
SEPARATE MACHINE
AND HAND HELD
FEED UNITS:


CWH
CWM

 .023(.5mm) - .030(.8mm) HARD CW-FC CWG030HS CWGHS CWT030  
.023(.5mm) - .030(.8mm) SOFT NOT RECOMMENDED CWH030HS CWGHS CWT030  
.035 (.9mm) HARD CW-FC CWG035HS CWGHS CWT035  
.035 (.9mm) SOFT CW-FCN CWG035HS CWGHS CWT035  
.045 (1.1mm) HARD CW-FC CWG045HS CWGHS CWT045  
3/64 (1.2mm) SOFT CW-FCN116 CWG116HS NONE NONE  
1/16 (1.6mm) HARD CW-FC116 CWG116HS NONE NONE  
1/16 (1.6mm) SOFT CW-FCN116 CWG116HS NONE NONE  

top
  home . contact . representation . technical information . pricing . site map

© CKWORLDWIDE, INC  2005